The WRT1200AC is the baby of the wrt_ac_series, with only 2 detachable antennas, and a slower processor. It is a dualband, 802.11ac wave 1 (80MHz) capable device.
Both revisions of the device are hardware identical, with changes made to the way wifi power tables are loaded into the device due to moves from Linksys in response to FCC changes.
Supported Versions
Experimental Versions
None at this time.
Hardware Highlights
Installation
→ Install OpenWrt (generic explanation)
Dual Firmware Flashing
The WRT AC series of routers uses a dual firmware flash layout.This means that two separate firmware partitions are included on the device and are flashed in an alternating fashion.
If booting from the primary partition, the secondary (or alternate) partition will be flashed on next sysupgrade, and booting is toggled to happen from that partition. The same logic applies to secondary-→primary. Note that this means there is no permanent “OEM partition” and “OpenWrt partition”. Both firmwares follow the same round-robin logic, where partition usage changes at each sysupgrade. The current firmware always remains as the fallback, and the new firmware is flashed to the other partition.
See the Flash Layout section on each device page for more details, or options to switch between partitions below.
It is recommended to install the LuCI package developed for managing dual firmware luci-app-advanced-reboot.
2016/05/18 13:26· JW0914
Flash Layout
If booting from primary partition, mtd5 will be named ubi, with mtd7 as ubi if booting from alternate partition
| Layer 0 | raw flash 128 MiB | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Layer 1 | mtd0u-boot1 MiB | mtd1u_env256 KiB | mtd2s_env256 KiB | mtd3devinfo1 MiB | firmware 80 MiB | mtd8syscfg38 MiB | mtd9unused_area6656 KiB | |||
| Layer 2 | mtd4kernel140 MiB | mtd6kernel240 MiB | ||||||||
| Layer 3 | primary kernel image 6 MiB | mtd5rootfs1 (ubi)34 MiB | alternate kernel image 6 MiB | mtd7rootfs2 (ubi)34 MiB | ||||||
OEM easy installation
OEM install
Login to Linksys WebUI (Default IP: 192.168.1.1; Password: admin)
Connectivity → Manual Update
Select factory image [.img]
Once flash completes, router will reboot
If the image selected
Has LuCI pre-installed:
Login to WebUI
Does not have LuCI pre-installed:
Login with SSH
Linux/BSD: SSH client built in
Windows: SSH client built in
Installing LuCI on uHTTPd
Login to WebUI
2016/05/18 13:26· JW0914
Upgrading OpenWrt
→ generic.sysupgrade
Sysupgrade
LuCI
Login to the OpenWrt WebUI (Default IP: 192.168.1.1)
System → Backup/Flash Firmware → Flash New Firmware Image → Choose File
Select Sysupgrade bin file [.bin]
Untick Keep Settings, then select Flash Image
CLI
Login to OpenWrt via SSH
Linux/BSD: SSH client built in
Windows: SSH client built in
Download/Upload firmware image to router
Download via SSH terminal:
cd /tmp && opkg update && opkg install wget && wget <Image-Link>
See AlsoUS Patent for Methods of treating cancer by administering an Axl ligand-binding portion of an Axl tyrosine kinase receptor extracellular domain Patent (Patent # 8,920,799 issued December 30, 2014)US Patent Application for AXL TYROSINE KINASE INHIBITORS AND METHODS OF MAKING AND USING THE SAME Patent Application (Application #20120230993 issued September 13, 2012)-- OR --
Upload via Client Machine Terminal:
scp -r -i "C:\OpenWrt.ppk" -2 -scp -P 22 "D:\Path\To\Firmware.img" root@192.168.1.1:/tmp
For PuTTY, change:
scptopscp -scp
-scp= force use of SCP protocol-r= copy directories recursively-i= private key file for user authentication-2= force use of particular SSH protocol version [2]-p= connect to specified port
Flash image
SSH terminal:
cd /tmp && sysupgrade -n -v <image-name>
-n= do not save configuration over reflash-v= more verbose
2016/05/18 13:26· JW0914
Return to Stock Firmware
Return to OEM
LuCI
Due to missing/incompatible metadata in OEM images, sysupgrade must be forced via the command line
CLI
Login to OpenWrt via SSH
Linux/BSD: SSH client built in
Windows: SSH client built in
Download/Upload firmware image to router
Download via SSH terminal:
cd /tmp && opkg update && opkg install wget && wget <Image-Link>
-- OR --
Upload via Client Machine Terminal:
scp -r -i "C:\OpenWrt.ppk" -2 -scp -P 22 "D:\Path\To\Firmware.img" root@192.168.1.1:/tmp
For PuTTY, change:
scptopscp -scp
-scp= force use of SCP protocol-r= copy directories recursively-i= private key file for user authentication-2= force use of particular SSH protocol version [2]-p= connect to specified port
Flash image
SSH terminal:
cd /tmp && sysupgrade -F -n -v <image-name>
-F= force write, required to bypass metadata check-n= do not save configuration over reflash-v= more verbose
2016/05/18 13:26· JW0914
Debricking
→ generic.debrick
If the U-Boot bootloader environment becomes corrupted, it can be reset
Reset Bootloader Environment
If the U-Boot bootloader becomes corrupted, it can be recovered
Recover Bootloader
Firmware Recovery
If the firmware has an issue, chances are you can recover it easily due to the Dual Firmware partition layout, by switching to the alternate firmware. For this reason, it is recommended to always keep a known working firmware on the other partition (either OEM or OpenWrt).
Switch router from primary to alternate partition or vice versa using any of the methods below:
LuCI
Install
luci-app-advanced-reboot:SSH:
opkg update && opkg install luci-app-advanced-reboot
WebUI:
System → Software
Actions → Update Lists
Actions → Filter
luci-app-advanced-reboot→ Find Package
Status: Available packages
Install
luci-app-advanced-reboot
System → Advanced Reboot
Serial
Connect via Serial:
reboot
At 3 second autoboot interrupt delay, press any key
Boot
Primary Partition
Armada XP
run linksysnandboot
Armada 385
run nandboot
Alternate Partition:
Armada XP
run linksysaltnandboot
Armada 385
run altnandboot
SSH
Determine current partition:
/usr/sbin/fw_printenv -n boot_part
Boot
Primary Partition:
/usr/sbin/fw_setenv boot_part 1 && reboot
Alternate Partition:
/usr/sbin/fw_setenv boot_part 2 && reboot
Power Switch
Power off router with power switch.
Turn power back on and power LED will light.
As soon as all LEDs turn off (~2s), power off router with power switch
Turn power back on and power LED will light.
As soon as all LEDs turn off (~2s), power off router with power switch
Turn power back on and power LED will light.
As soon as all LEDs turn off (~2s), power off router with power switch
Turn power back on and allow router to fully boot.
It should now be booted to the alternate firmware partition
Explanation:There is a counter for boot attempts. The counter is increased by 1 at the start of each boot process, then is reset to 0 after a successful boot. If the counter reaches 3, the boot is considered a failure and the boot partition is switched to the other partition (A-→B or B-→A).
Thus, if you interrupt the boot process three times, the router thinks that the current firmware is faulty and switches to the other partition. Note that there is no guarantee that the other partition works. It has the contents and settings that were there when the boot was switched last time, usually at the last sysupgrade. That boot marker switch (A-→B or B-→A) happens at every sysupgrade, so likely you just have the previously used firmware there (either OEM or OpenWrt). But the marker may have been manually toggled, or auto-toggled after three failures.
2016/05/18 13:26· JW0914
Failsafe mode
→ failsafe_and_factory_reset
Basic configuration
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
Switch Ports (for VLANs)
eth0/eth1: physical PCB connectionLAN: physical LAN ports on routerWAN: physical Internet port on router
Marvell 88E6176 (WRT1200AC)
| sw.port | 0 | 1 | 2 | 3 | 4 | 5 | 6 | vlan ID |
|---|---|---|---|---|---|---|---|---|
| LAN | 4 | 3 | 2 | 1 | -- | eth1 | -- | 1 |
| WAN | -- | -- | -- | -- | Internet | -- | eth0 | 2 |
Buttons
→ hardware.button on howto use and configure the hardware button(s).Here, we merely name the buttons, so we can use them in the above Howto.
| BUTTON | Event |
|---|---|
| Reset | reset |
| WPS | wps |
Hardware
Info
Photos
Front:
Back:
Backside label:
Opening the case
Note: This will void your warranty!
Remove front foot screws
Pull front blue cover straight forward slowly, but firmly
Remove rear foot screws
Gently pry up rear, black top cover using plastic spudgers/opening tool
There are two plastic guides, one per side, which slide into the rear feet
Main PCB:
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
| Serial connection parameters | 115200, 8N1 |
|---|
Serial Port
Synopsis
Serial Port is labeled J1 on the board, utilizing a JST PH 6 pin connector with a 2.0mm pitch, operating at 3.3v
The more common 2.54mm pitch will not fit properly.
In a pinch, removing the plastic casing from 2.54mm female connectors allows for a stable enough connection.
Ensure leads are insulated with electrical tape
If flashing regularly, you may wish to invest in a USB-TTL AJ cable
USB-TTL AJ cables require installation of a 3.5mm Jack (F) on the router
Serial Header
| Pin Out | ||||||
|---|---|---|---|---|---|---|
| Pins | 1 | 2 | 3 | 4 | 5 | 6 |
| Function | Gnd | Tx | n/a | Rx | n/a | n/a |
2016/05/18 13:26· JW0914
Marvell Wifi
This device uses the Marvell Wifi mwlwifi driver. You can read more about it here: Marvell Wifi
Bootloader mods
→ bootloader
Hardware mods
USB-TTL Audio Jack Install
Bootlogs
OEM bootlog
BootROM - 1.73Booting from NAND flashGeneral initialization - Version: 1.0.0AVS selection from EFUSE disabled (Skip reading EFUSE values)Overriding default AVS value to: 0x23mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failedDetected Device ID 6820High speed PHY - Version: 2.0Init RD NAS topology Serdes Lane 3 is USB3Serdes Lane 4 is SGMIIboard SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 6 | SATA0 | | 1 | 5 | PCIe0 | | 2 | 6 | SATA1 | | 3 | 5 | USB3 HOST1 | | 4 | 5 | PCIe1 | | 5 | 0 | SGMII2 | -------------------------------:** Link is Gen1, check the EP capability PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities :** Link is Gen1, check the EP capability PCIe, Idx 1: remains Gen1High speed PHY - Ended SuccessfullyDDR3 Training Sequence - Ver TIP-1.56.0mvSysEnvGetTopologyUpdateInfo: TWSI Read failedDDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended SuccessfullyNot detected suspend to RAM indicationBootROM: Image checksum verification PASSED __ __ _ _| \/ | __ _ _ ____ _____| | || |\/| |/ _` | '__\ \ / / _ \ | || | | | (_| | | \ V / __/ | ||_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER **U-Boot 2013.01 (Jun 01 2018 - 18:43:27) Marvell version: 2015_T1.0p19Boot version : v2.2.16Board: RD-NAS-88F6820-DDR3SoC: MV88F6820 Rev A0 running 2 CPUsCPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR3 @ 666 [MHz] DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC DisabledDRAM: 512 MiBNAND: 128 MiBMMC: mv_sdh: 0DEVINFO offset == 0x900000U-ENV offset == 0x200000U-ENV offset == 0x200000S-ENV offset == 0x240000#### auto_recovery ####[u_env] get auto_recovery == yes[u_env] get auto_recovery == yes[u_env] get boot_part == 1[u_env] get boot_part_ready == 3auto_recovery enabled:1, boot_part:1, boot_part_ready:3 S-ENV offset == 0x240000[boot_count_read] block:0x240000, size:128KB, records:64 [boot_count_read_record] boot_count:1, next_record:3[boot_count_write] erase:0, auto_recovery->block_offset:0x240000 offset=0x241800Updating boot_count ... [boot_count_write] offset:0x241800 , length:2048donePCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1USB2.0 0: Host ModeUSB3.0 1: Host ModeUSB3.0 0: Host ModeMap: Code: 0x1feab000:0x1ff75b48 BSS: 0x1ffef0e4 Stack: 0x1f9aaf20 Heap: 0x1f9ab000:0x1feab000U-ENV offset == 0x200000U-ENV offset == 0x200000 U-Boot Environment: 0x00200000:0x00220000 (NAND)Board configuration detected:mvEthE6171SwitchBasicInit init Net: | port | Interface | PHY address ||--------|-----------|--------------|| egiga0 | RGMII | 0x01 || egiga1 | SGMII | 0x00 || egiga2 | SGMII | In-Band |egiga0 [PRIME], egiga1, egiga2auto_recovery_check changes bootcmd: run nandboot Hit any key to stop autoboot: 0 NAND read: device 0 offset 0xa00000, size 0x600000 6291456 bytes read: OK## Booting kernel from Legacy Image at 02000000 ... Image Name: Linksys WRT1200AC Router Created: 2018-11-14 21:18:36 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4219619 Bytes = 4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OKOKStarting kernel ...Uncompressing Linux... done, booting the kernel.Booting Linux on physical CPU 0x0Linux version 3.10.39 (root@build-vm) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 SMP Wed Nov 14 13:18:20 PST 2018CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7dCPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cacheMachine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Boardbootconsole [earlycon0] enabledMemory policy: ECC disabled, Data cache writeallocPERCPU: Embedded 7 pages/cpu @c0ffe000 s8000 r8192 d12480 u32768Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048Kernel command line: console=ttyS0,115200 root=/dev/mtdblock5 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,256K(u_env),256K(s_env),1m@9m(devinfo),40m@10m(kernel),34m@16m(rootfs),40m@50m(alt_kernel),34m@56m(alt_rootfs),80m@10m(ubifs),-@90m(syscfg)PID hash table entries: 2048 (order: 1, 8192 bytes)Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)allocated 1048576 bytes of page_cgroupplease try 'cgroup_disable=memory' option if you don't want memory cgroupsMemory: 512MB = 512MB totalMemory: 509780k/509780k available, 14508k reserved, 0K highmemVirtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc075be24 (7504 kB) .init : 0xc075c000 - 0xc079bf40 ( 256 kB) .data : 0xc079c000 - 0xc07eb8e0 ( 319 kB) .bss : 0xc07eb8e0 - 0xc08a2458 ( 731 kB)Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p5sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798msL310 cache controller enabledl2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 BConsole: colour dummy device 80x30Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232)pid_max: default: 32768 minimum: 301Mount-cache hash table entries: 512Initializing cgroup subsys memoryCPU: Testing write buffer coherency: okCPU0: thread -1, cpu 0, socket 0, mpidr 80000000Setting up static identity map for 0xc05a27d0 - 0xc05a2828mvebu-pmsu: Initializing Power Management Service UnitInitializing CPU Reset moduleCPU1: Booted secondary processorCPU1: thread -1, cpu 1, socket 0, mpidr 80000001Brought up 2 CPUsSMP: Total of 2 processors activated (5311.69 BogoMIPS).CPU: All CPU(s) started in SVC mode.devtmpfs: initializedmvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4xor: measuring software checksum speed arm4regs : 2361.600 MB/sec 8regs : 1594.800 MB/sec 32regs : 1360.000 MB/secxor: using function: arm4regs (2361.600 MB/sec)pinctrl core: initialized pinctrl subsystemNET: Registered protocol family 16DMA: preallocated 256 KiB pool for atomic coherent allocationsirq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocatedirq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocatedbio: create slab <bio-0> at 0raid6: int32x1 166 MB/sraid6: int32x2 245 MB/sraid6: int32x4 312 MB/sraid6: int32x8 316 MB/sraid6: using algorithm int32x8 (316 MB/s)raid6: using intx1 recovery algorithmmvebu-pcie pcie-controller.6: PCIe0.0: link upmvebu-pcie pcie-controller.6: PCIe1.0: link upmvebu-pcie pcie-controller.6: ignoring PCIe DT node, missing pcie-port propertymvebu-pcie pcie-controller.6: PCI host bridge to bus 0000:00pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000]pci_bus 0000:00: root bus resource [bus 00-ff]PCI: bus0: Fast back to back transfers disabledpci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguringpci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguringPCI: bus1: Fast back to back transfers disabledPCI: bus2: Fast back to back transfers disabledpci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe01fffff]pci 0000:00:02.0: BAR 8: assigned [mem 0xe0200000-0xe03fffff]pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit pref]pci 0000:01:00.0: BAR 2: assigned [mem 0xe0100000-0xe01fffff 64bit pref]pci 0000:00:01.0: PCI bridge to [bus 01]pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe01fffff]pci 0000:02:00.0: BAR 0: assigned [mem 0xe0200000-0xe02fffff 64bit pref]pci 0000:02:00.0: BAR 2: assigned [mem 0xe0300000-0xe03fffff 64bit pref]pci 0000:00:02.0: PCI bridge to [bus 02]pci 0000:00:02.0: bridge window [mem 0xe0200000-0xe03fffff]PCI: enabling device 0000:00:01.0 (0140 -> 0143)PCI: enabling device 0000:00:02.0 (0140 -> 0143)SCSI subsystem initializedusbcore: registered new interface driver usbfsusbcore: registered new interface driver hubusbcore: registered new device driver usbpps_core: LinuxPPS API ver. 1 registeredpps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>PTP clock support registeredBluetooth: Core ver 2.16NET: Registered protocol family 31Bluetooth: HCI device and connection manager initializedBluetooth: HCI socket layer initializedBluetooth: L2CAP socket layer initializedBluetooth: SCO socket layer initializedSwitching to clocksource armada_370_xp_clocksourcecfg80211: Calling CRDA to update world regulatory domainNET: Registered protocol family 2TCP established hash table entries: 4096 (order: 3, 32768 bytes)TCP bind hash table entries: 4096 (order: 3, 32768 bytes)TCP: Hash tables configured (established 4096 bind 4096)TCP: reno registeredUDP hash table entries: 256 (order: 1, 8192 bytes)UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)NET: Registered protocol family 1RPC: Registered named UNIX socket transport module.RPC: Registered udp transport module.RPC: Registered tcp transport module.RPC: Registered tcp NFSv4.1 backchannel transport module.jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.fuse init (API version 7.22)msgmni has been set to 995async_tx: api initialized (async)Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)io scheduler noop registeredio scheduler deadline registeredio scheduler cfq registered (default)armada-38x-pinctrl f1018000.pinctrl: registered pinctrl drivermv_xor f1060800.xor: Marvell shared XOR drivermv_xor f1060800.xor: Marvell XOR: ( xor cpy intr )mv_xor f1060800.xor: freeing 1 in use descriptors!mv_xor f1060800.xor: Marvell XOR: ( crc32c )mv_xor f1060900.xor: Marvell shared XOR drivermv_xor f1060900.xor: Marvell XOR: ( xor cpy intr )mv_xor f1060900.xor: freeing 1 in use descriptors!mv_xor f1060900.xor: Marvell XOR: ( crc32c )Serial: 8250/16550 driver, 4 ports, IRQ sharing disabledf1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550Aconsole [ttyS0] enabled, bootconsole disabledconsole [ttyS0] enabled, bootconsole disabledahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform modeahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platformscsi1 : ahci_mv_platformata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECCNAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD/Spansion NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64Bad block table found at page 65472, version 0x01Bad block table found at page 65408, version 0x0110 cmdlinepart partitions found on MTD device armada-nandCreating 10 MTD partitions on "armada-nand":0x000000000000-0x000000200000 : "uboot"0x000000200000-0x000000240000 : "u_env"0x000000240000-0x000000280000 : "s_env"0x000000900000-0x000000a00000 : "devinfo"0x000000a00000-0x000003200000 : "kernel"0x000001000000-0x000003200000 : "rootfs"0x000003200000-0x000005a00000 : "alt_kernel"0x000003800000-0x000005a00000 : "alt_rootfs"0x000000a00000-0x000005a00000 : "ubifs"0x000005a00000-0x000008000000 : "syscfg"bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)tun: Universal TUN/TAP device driver, 1.6tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>SoC: model = 0x6820, revision = 0x4mvPncVirtBase = 0xe0c00000, pncTcamSize = 1024 o 3 Giga ports supported o SKB recycle supported (Disabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o Receive checksum offload supported o Transmit checksum offload supportedport #0: is_sgmii=0, is_rgmii=1, phy_addr=0 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o eth0, ifindex = 3, GbE port = 0 giga p=0: mtu=1500, mac=30:23:03:93:be:ea (hw config)port #2: is_sgmii=1, is_rgmii=0, phy_addr=1 o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048 o Port 2 is connected to Linux netdevice o eth1, ifindex = 4, GbE port = 2 giga p=2: mtu=1500, mac=36:15:20:d6:2f:5a (random) o Loading Switch QuarterDeck driver o Device ID : 0x176 o No. of Ports : 7 o CPU Port : 5Switch driver init: o preset mode = Transparent o tag mode = No Tagport #0 establish switch connectionlibphy: orion_mdio_bus: probedmdio_bus f1072004.mdio-mi: cannot get PHY at address 0mdio_bus f1072004.mdio-mi: cannot get PHY at address 1PPP generic driver version 2.4.2PPP BSD Compression module registeredPPP Deflate Compression module registeredNET: Registered protocol family 24PPTP driver version 0.8.5ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driverehci-pci: EHCI PCI platform driverehci-orion: EHCI orion driverorion-ehci f1058000.usb: EHCI Host Controllerorion-ehci f1058000.usb: new USB bus registered, assigned bus number 1orion-ehci f1058000.usb: irq 50, io mem 0xf1058000orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00hub 1-0:1.0: USB hub foundhub 1-0:1.0: 1 port detectedata1: SATA link down (SStatus 0 SControl 300)ata2: SATA link down (SStatus 0 SControl 300)xhci-hcd f10f0000.usb3: xHCI Host Controllerxhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000hub 2-0:1.0: USB hub foundhub 2-0:1.0: 1 port detectedxhci-hcd f10f0000.usb3: xHCI Host Controllerxhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3hub 3-0:1.0: USB hub foundhub 3-0:1.0: 1 port detectedxhci-hcd f10f8000.usb3: xHCI Host Controllerxhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000hub 4-0:1.0: USB hub foundhub 4-0:1.0: 1 port detectedxhci-hcd f10f8000.usb3: xHCI Host Controllerxhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5hub 5-0:1.0: USB hub foundhub 5-0:1.0: 1 port detectedmvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0i2c /dev entries drivermd: raid0 personality registered for level 0md: raid1 personality registered for level 1md: raid6 personality registered for level 6md: raid5 personality registered for level 5md: raid4 personality registered for level 4cpuidle: using governor laddersdhci: Secure Digital Host Controller Interface driversdhci: Copyright(c) Pierre Ossmanmmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMAsdhci-pltfm: SDHCI platform and OF driver helperarmada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: int_coalescing(1)armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources threshold 0x2, threshold_time 0xffmvCesaInit: channels=2, session=640, queue=256armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) modecesadev_init(c0777eec)usbcore: registered new interface driver usbhidusbhid: USB HID core driverNET: Registered protocol family 26u32 classifierNetfilter messages via NETLINK v0.30.nfnl_acct: registering with nfnetlink.nf_conntrack version 0.5.0 (7965 buckets, 31860 max)ctnetlink v0.93: registering with nfnetlink.nf_conntrack_rtsp v0.7 loadingipip: IPv4 over IPv4 tunneling drivergre: GRE over IPv4 demultiplexor driverip_gre: GRE over IPv4 tunneling drivernf_nat_rtsp v0.7 loadingip_tables: (C) 2000-2006 Netfilter Core Teamarp_tables: (C) 2002 David S. MillerTCP: cubic registeredNET: Registered protocol family 10ip6_tables: (C) 2000-2006 Netfilter Core Teamsit: IPv6 over IPv4 tunneling driverNET: Registered protocol family 17Bridge firewalling registeredEbtables v2.0 registeredl2tp_core: L2TP core driver, V2.0l2tp_ppp: PPPoL2TP kernel driver, V2.08021q: 802.1Q VLAN Support v1.8Key type dns_resolver registeredVFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4Port 3: Link-up, Full-duplex, Speed-100Mbps.input: gpio_keys.4 as /devices/soc.0/internal-regs.1/gpio_keys.4/input/input0mvebu-rtc f10a3800.rtc: setting system clock to 1970-01-01 00:00:01 UTC (1)Waiting 1sec before mounting root device...md: Waiting for all devices to be available before autodetectmd: If you don't use raid, use raid=noautodetectmd: Autodetecting RAID arrays.md: Scanned 0 and added 0 devices.md: autorun ...md: ... autorun DONE.jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01800000: 0x4c2e insteadjffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01800004: 0x534b insteadjffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01800008: 0x302e insteadjffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0180000c: 0x3030 insteadjffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01800010: 0x5743 insteadjffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01800014: 0x3231 insteadjffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01800018: 0x4341 insteadjffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0180001c: 0x2020 insteadjffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01800020: 0x3030 insteadjffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01800024: 0x3744 insteadjffs2: Further such events for this erase block will not be printedVFS: Mounted root (jffs2 filesystem) readonly on device 31:5.devtmpfs: mountedFreeing unused kernel memory: 252K (c075c000 - c079b000)********************************************************************************* _ _ __ _ __ _____ __ __ _____ | | | || \ | | / // ____]\ \ / // ____]TM | | | || \ | | / /| (___ \ V /| (____ | | | || |\ \| |\ \ \____ \ \ / \____ \ | |_____ | || | \ | \ \ ____) | | | ____) | |_______||_||_| \__| \_\[____ / |_| [_____/ (c) 2015 Belkin International, Inc. and/or its affiliates. All rights reserved. Booting caiman (firmware version 2.0.6.191786) *********************************************************************************[utopia][init] System Initialization[utopia][init] Creating /proc[utopia][init] Creating /sys[utopia][init] Creating /dev[utopia][init] Creating /tmp[utopia][init] Allocating 100M for /tmp[utopia][init] Prepairing /dev/pts[utopia][init] Setting /tmp and /var permissions[utopia][init] Starting udev..orion_wdt: Initial timeout 171 secAttempting mount of ubifs syscfg partitionUBI device number 0, total 296 LEBs (37584896 bytes, 35.8 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)[utopia][init] Using persistent syscfg data from /var/config/syscfg[utopia][init] Starting system logging[utopia][init] Starting sysevent subsystemnet.netfilter.nf_conntrack_acct = 1watchdog running[utopia][init] Setting any unset system values to defaultmac_setup.sh, setting up MAC addresses for all interfaces based on 30:23:03:93:BE:EANTP Servers do not need to be updated[utopia][init] committing default syscfg valueschecking for interactive script start up...Updating BootCount Page[4]:2000 ... Donecpu temp monitor createdThu Oct 11 06:00:00 UTC 2012wdev0 no private ioctls.wdev1 no private ioctls.wan, sysevent received: wan-startLighttpd Model Base: WRT1200ACGenerating Rainier lighttpd config Creating /tmp/var/config/license Build temporary www configuration directory: TSLIIHauhEfGE wifi, sysevent received: lan-started (Wed Oct 10 23:00:05 PDT 2012) wifi, service_start() Power cycle Ethernet ports. Registering Service myrouter._http._tcp.local port 80 Got a reply for myrouter._http._tcp.local.: Name now registered and active Not ready for JNAP. Sleeping for 15 seconds... SKU is WRT1200AC-AP wifi, wifi_physical_start(wdev0) wifi_physical, iwconfig wdev0 commit wifi, wifi_virtual_start(wdev0) wifi, wifi_user_start(wdev0) wifi, primary AP: wdev0ap0 is up [utopia] Not setting ppp_clamp_mtu wifi, wifi_guest_start(wdev0) wifi, guest wdev0ap1 is disabled, do not start wifi guest wifi, wifi_physical_start(wdev1) wifi_physical, iwconfig wdev1 commit wifi, wifi_virtual_start(wdev1) wifi, wifi_user_start(wdev1) wifi, primary AP: wdev1ap0 is up wifi, wifi_guest_start(wdev1) wifi, guest wdev1ap1 is disabled, do not start wifi guest wifi, start_hostapd() Configuration file: /tmp/hostapd-wdev1ap0.conf Using interface wdev1ap0 with hwaddr 30:23:03:93:be:eb and ssid "Linksys00178" Configuration file: /tmp/hostapd-wdev0ap0.conf Using interface wdev0ap0 with hwaddr 30:23:03:93:be:ec and ssid "Linksys00178_5GHz" Restarting nfqrecv service... Got a TERM signal, will terminate. Warning! nfqrecv encountered errors when doing recv(): Interrupted system call [utopia] Not setting ppp_clamp_mtu on dslite protocol wan, sysevent received: phylink_wan_state Starting smbd ...
OpenWrt bootlog
[ 0.000000] Booting Linux on physical CPU 0x0[ 0.000000] Linux version 4.14.162 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10860-a3ffeb413b)) #0 SMP Mon Jan 6 16:47:09 2020[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache[ 0.000000] OF: fdt: Machine model: Linksys WRT1200AC[ 0.000000] Memory policy: Data cache writealloc[ 0.000000] On node 0 totalpages: 131072[ 0.000000] free_area_init_node: node 0, pgdat c0931340, node_mem_map dfbf9000[ 0.000000] Normal zone: 1024 pages used for memmap[ 0.000000] Normal zone: 0 pages reserved[ 0.000000] Normal zone: 131072 pages, LIFO batch:31[ 0.000000] random: get_random_bytes called from 0xc08008bc with crng_init=0[ 0.000000] percpu: Embedded 11 pages/cpu s14860 r8192 d22004 u45056[ 0.000000] pcpu-alloc: s14860 r8192 d22004 u45056 alloc=11*4096[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock7 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,256K(u_env),256K(s_env),1m@9m(devinfo),40m@10m(kernel),34m@16m(rootfs),40m@50m(alt_kernel),34m@56m(alt_rootfs),80m@10m(ubifs),-@90m(syscfg)[ 0.000000] Bootloader command line (ignored): console=ttyS0,115200 root=/dev/mtdblock7 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,256K(u_env),256K(s_env),1m@9m(devinfo),40m@10m(kernel),34m@16m(rootfs),40m@50m(alt_kernel),34m@56m(alt_rootfs),80m@10m(ubifs),-@90m(syscfg)[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)[ 0.000000] Memory: 510928K/524288K available (6144K kernel code, 199K rwdata, 816K rodata, 1024K init, 233K bss, 13360K reserved, 0K cma-reserved, 0K highmem)[ 0.000000] Virtual kernel memory layout:[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)[ 0.000000] .text : 0xc0008000 - 0xc0700000 (7136 kB)[ 0.000000] .init : 0xc0800000 - 0xc0900000 (1024 kB)[ 0.000000] .data : 0xc0900000 - 0xc0931c40 ( 200 kB)[ 0.000000] .bss : 0xc0931c40 - 0xc096c098 ( 234 kB)[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1[ 0.000000] Hierarchical RCU implementation.[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001[ 0.000007] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns[ 0.000018] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns[ 0.000033] Switching to timer-based delay loop, resolution 1ns[ 0.000165] Ignoring duplicate/late registration of read_current_timer delay[ 0.000173] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns[ 0.000328] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000)[ 0.000336] pid_max: default: 32768 minimum: 301[ 0.000397] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)[ 0.000403] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)[ 0.000655] CPU: Testing write buffer coherency: ok[ 0.000668] CPU0: Spectre v2: using BPIALL workaround[ 0.000783] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000[ 0.000909] Setting up static identity map for 0x100000 - 0x100060[ 0.000989] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4[ 0.001072] mvebu-pmsu: Initializing Power Management Service Unit[ 0.001125] Hierarchical SRCU implementation.[ 0.001335] smp: Bringing up secondary CPUs ...[ 0.001471] Booting CPU 1[ 0.001640] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001[ 0.001643] CPU1: Spectre v2: using BPIALL workaround[ 0.001699] smp: Brought up 1 node, 2 CPUs[ 0.001705] SMP: Total of 2 processors activated (2664.00 BogoMIPS).[ 0.001709] CPU: All CPU(s) started in SVC mode.[ 0.003471] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4[ 0.003529] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns[ 0.003537] futex hash table entries: 512 (order: 3, 32768 bytes)[ 0.003590] pinctrl core: initialized pinctrl subsystem[ 0.003951] NET: Registered protocol family 16[ 0.004616] DMA: preallocated 256 KiB pool for atomic coherent allocations[ 0.005155] cpuidle: using governor ladder[ 0.005349] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling[ 0.005357] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling[ 0.011890] reg-fixed-voltage usb3_1-vbus: could not find pctldev for node /soc/internal-regs/pinctrl@18000/usb3_1-vbus-pins, deferring probe[ 0.012080] SCSI subsystem initialized[ 0.012176] libata version 3.00 loaded.[ 0.012281] usbcore: registered new interface driver usbfs[ 0.012314] usbcore: registered new interface driver hub[ 0.012344] usbcore: registered new device driver usb[ 0.012975] clocksource: Switched to clocksource arm_global_timer[ 0.013364] NET: Registered protocol family 2[ 0.013667] TCP established hash table entries: 4096 (order: 2, 16384 bytes)[ 0.013693] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)[ 0.013732] TCP: Hash tables configured (established 4096 bind 4096)[ 0.013771] UDP hash table entries: 256 (order: 1, 8192 bytes)[ 0.013787] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)[ 0.013857] NET: Registered protocol family 1[ 0.013872] PCI: CLS 0 bytes, default 64[ 0.014895] Crashlog allocated RAM at address 0x3f00000[ 0.014977] workingset: timestamp_bits=30 max_order=17 bucket_order=0[ 0.016805] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.016813] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.[ 0.018223] io scheduler noop registered[ 0.018230] io scheduler deadline registered (default)[ 0.018740] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver[ 0.019873] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00[ 0.019884] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff][ 0.019890] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff][ 0.019896] pci_bus 0000:00: root bus resource [bus 00-ff][ 0.019914] pci 0000:00:01.0: [11ab:6820] type 01 class 0x060400[ 0.020016] pci 0000:00:02.0: [11ab:6820] type 01 class 0x060400[ 0.020105] PCI: bus0: Fast back to back transfers disabled[ 0.020112] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring[ 0.020120] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring[ 0.020177] pci 0000:01:00.0: [11ab:2a55] type 00 class 0x020000[ 0.020203] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x400fffff 64bit pref][ 0.020214] pci 0000:01:00.0: reg 0x18: [mem 0x40100000-0x401fffff 64bit pref][ 0.020277] pci 0000:01:00.0: supports D1 D2[ 0.020281] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold[ 0.020345] PCI: bus1: Fast back to back transfers disabled[ 0.020354] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01[ 0.020411] pci 0000:02:00.0: [11ab:2a55] type 00 class 0x020000[ 0.020441] pci 0000:02:00.0: reg 0x10: [mem 0x42000000-0x420fffff 64bit pref][ 0.020454] pci 0000:02:00.0: reg 0x18: [mem 0x42100000-0x421fffff 64bit pref][ 0.020537] pci 0000:02:00.0: supports D1 D2[ 0.020541] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold[ 0.020607] PCI: bus2: Fast back to back transfers disabled[ 0.020615] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02[ 0.020634] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe01fffff][ 0.020641] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0200000-0xe03fffff][ 0.020649] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit pref][ 0.020661] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0100000-0xe01fffff 64bit pref][ 0.020671] pci 0000:00:01.0: PCI bridge to [bus 01][ 0.020678] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe01fffff][ 0.020686] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0200000-0xe02fffff 64bit pref][ 0.020698] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0300000-0xe03fffff 64bit pref][ 0.020709] pci 0000:00:02.0: PCI bridge to [bus 02][ 0.020715] pci 0000:00:02.0: bridge window [mem 0xe0200000-0xe03fffff][ 0.020988] mv_xor f1060800.xor: Marvell shared XOR driver[ 0.083552] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )[ 0.083680] mv_xor f1060900.xor: Marvell shared XOR driver[ 0.143488] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )[ 0.143659] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled[ 0.144430] console [ttyS0] disabled[ 0.164505] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 12500000) is a 16550A[ 0.937038] console [ttyS0] enabled[ 0.942236] loop: module loaded[ 0.945744] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode[ 0.954851] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 0.964066] scsi host0: ahci-mvebu[ 0.967634] scsi host1: ahci-mvebu[ 0.971129] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41[ 0.979103] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41[ 0.987503] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device[ 0.995314] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1[ 1.001701] nand: AMD/Spansion S34ML01G2[ 1.005654] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64[ 1.013280] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048[ 1.020474] Bad block table found at page 65472, version 0x01[ 1.026606] Bad block table found at page 65408, version 0x01[ 1.032670] 10 fixed-partitions partitions found on MTD device pxa3xx_nand-0[ 1.039762] Creating 10 MTD partitions on "pxa3xx_nand-0":[ 1.045281] 0x000000000000-0x000000200000 : "u-boot"[ 1.050534] 0x000000200000-0x000000240000 : "u_env"[ 1.055660] 0x000000240000-0x000000280000 : "s_env"[ 1.060768] 0x000000900000-0x000000a00000 : "devinfo"[ 1.066082] 0x000000a00000-0x000003200000 : "kernel1"[ 1.071467] 0x000001000000-0x000003200000 : "rootfs1"[ 1.076845] 0x000003200000-0x000005a00000 : "kernel2"[ 1.082226] 0x000003800000-0x000005a00000 : "ubi"[ 1.087253] 0x000005a00000-0x000008000000 : "syscfg"[ 1.092548] 0x000000280000-0x000000900000 : "unused_area"[ 1.098568] libphy: Fixed MDIO Bus: probed[ 1.103042] libphy: orion_mdio_bus: probed[ 1.107353] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled[ 1.116259] mvneta f1070000.ethernet eth0: Using hardware mac address c0:56:27:03:02:01[ 1.125731] mvneta f1034000.ethernet eth1: Using random mac address 02:8e:f0:01:02:03[ 1.133789] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver[ 1.140352] ehci-pci: EHCI PCI platform driver[ 1.144851] ehci-platform: EHCI generic platform driver[ 1.150183] ehci-orion: EHCI orion driver[ 1.154315] orion-ehci f1058000.usb: EHCI Host Controller[ 1.159753] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1[ 1.167419] orion-ehci f1058000.usb: irq 38, io mem 0xf1058000[ 1.212983] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00[ 1.219183] hub 1-0:1.0: USB hub found[ 1.222978] hub 1-0:1.0: 1 port detected[ 1.227411] usbcore: registered new interface driver usb-storage[ 1.233646] i2c /dev entries driver[ 1.248556] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().[ 1.261035] orion_wdt: Initial timeout 171 sec[ 1.265801] sdhci: Secure Digital Host Controller Interface driver[ 1.272011] sdhci: Copyright(c) Pierre Ossman[ 1.276505] sdhci-pltfm: SDHCI platform and OF driver helper[ 1.285949] marvell-cesa f1090000.crypto: CESA device successfully registered[ 1.293606] NET: Registered protocol family 10[ 1.298600] Segment Routing with IPv6[ 1.302312] NET: Registered protocol family 17[ 1.306807] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.[ 1.314577] ata2: SATA link down (SStatus 0 SControl 300)[ 1.325405] 8021q: 802.1Q VLAN Support v1.8[ 1.325411] ata1: SATA link down (SStatus 0 SControl 300)[ 1.329674] Registering SWP/SWPB emulation handler[ 1.341565] xhci-hcd f10f8000.usb3: xHCI Host Controller[ 1.346941] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 2[ 1.354547] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010[ 1.363847] xhci-hcd f10f8000.usb3: irq 43, io mem 0xf10f8000[ 1.369918] hub 2-0:1.0: USB hub found[ 1.373718] hub 2-0:1.0: 1 port detected[ 1.377786] xhci-hcd f10f8000.usb3: xHCI Host Controller[ 1.383144] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3[ 1.390676] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed[ 1.397193] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.[ 1.405534] hub 3-0:1.0: USB hub found[ 1.409319] hub 3-0:1.0: 1 port detected[ 1.413659] UBI: auto-attach mtd7[ 1.416993] ubi0: attaching mtd7[ 1.427976] random: fast init done[ 1.518167] ubi0: scanning is finished[ 1.526479] ubi0: attached mtd7 (name "ubi", size 34 MiB)[ 1.531908] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 1.538832] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 1.545661] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096[ 1.552657] ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0[ 1.558699] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128[ 1.565964] ubi0: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 1673440142[ 1.575148] ubi0: available PEBs: 0, total reserved PEBs: 272, PEBs reserved for bad PEB handling: 20[ 1.584425] ubi0: background thread "ubi_bgt0d" started, PID 697[ 1.584845] block ubiblock0_0: created from ubi0:0(rootfs)[ 1.595989] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem[ 1.603207] mvsw61xx 10.mvsw61xx: Found MV88E6176 at f1072004.mdio-mii:10[ 1.610031] mvsw61xx 10.mvsw61xx: Using direct addressing[ 1.625694] hctosys: unable to open rtc device (rtc0)[ 1.631170] Waiting 1 sec before mounting root device...[ 2.725064] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.[ 2.732892] Freeing unused kernel memory: 1024K[ 2.960537] init: Console is alive[ 2.964045] init: - watchdog -[ 3.187653] kmodloader: loading kernel modules from /etc/modules-boot.d/*[ 3.225441] kmodloader: done loading kernel modules from /etc/modules-boot.d/*[ 3.239340] init: - preinit -[ 3.458781] mvneta f1070000.ethernet tmp0: renamed from eth0[ 3.464787] random: procd: uninitialized urandom read (4 bytes read)[ 3.494711] mvneta f1034000.ethernet eth0: renamed from eth1[ 3.534669] mvneta f1070000.ethernet eth1: renamed from tmp0[ 3.831624] random: jshn: uninitialized urandom read (4 bytes read)[ 3.872287] random: jshn: uninitialized urandom read (4 bytes read)[ 4.094620] mvneta f1034000.ethernet eth0: configuring for fixed/sgmii link mode[ 4.102528] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready[ 4.108630] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off[ 4.116558] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready[ 7.220632] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 809[ 7.249943] UBIFS (ubi0:1): recovery needed[ 7.306265] UBIFS (ubi0:1): recovery completed[ 7.310772] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"[ 7.318652] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes[ 7.328624] UBIFS (ubi0:1): FS size: 27680768 bytes (26 MiB, 218 LEBs), journal size 1396736 bytes (1 MiB, 11 LEBs)[ 7.339116] UBIFS (ubi0:1): reserved for root: 1307430 bytes (1276 KiB)[ 7.345770] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 540D9A8F-C508-4EB8-B135-010203040506, small LPT model[ 7.363255] mount_root: switching to ubifs overlay[ 7.434313] ubi1: attaching mtd8[ 7.540760] ubi1: scanning is finished[ 7.549115] ubi1: attached mtd8 (name "syscfg", size 38 MiB)[ 7.554824] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 7.561734] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 7.568562] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096[ 7.575564] ubi1: good PEBs: 296, bad PEBs: 8, corrupted PEBs: 0[ 7.581601] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128[ 7.588865] ubi1: max/mean erase counter: 24/16, WL threshold: 4096, image sequence number: 40071263[ 7.598049] ubi1: available PEBs: 0, total reserved PEBs: 296, PEBs reserved for bad PEB handling: 12[ 7.607327] ubi1: background thread "ubi_bgt1d" started, PID 817[ 7.618575] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 823[ 7.671788] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "syscfg"[ 7.679235] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes[ 7.689207] UBIFS (ubi1:0): FS size: 34283520 bytes (32 MiB, 270 LEBs), journal size 1777664 bytes (1 MiB, 14 LEBs)[ 7.699699] UBIFS (ubi1:0): reserved for root: 1619295 bytes (1581 KiB)[ 7.706352] UBIFS (ubi1:0): media format: w4/r0 (latest is w5/r0), UUID 1B24EEA1-525F-44A0-B992-010203040506, small LPT model[ 7.719563] urandom-seed: Seeding with /etc/urandom.seed[ 7.762554] mvneta f1034000.ethernet eth0: Link is Down[ 7.832915] random: crng init done[ 7.836340] random: 3 urandom warning(s) missed due to ratelimiting[ 7.845645] procd: - early -[ 7.849132] procd: - watchdog -[ 8.451203] procd: - watchdog -[ 8.454471] procd: - ubus -[ 8.507802] procd: - init -[ 8.711718] kmodloader: loading kernel modules from /etc/modules.d/*[ 8.719986] ip6_tables: (C) 2000-2006 Netfilter Core Team[ 8.727688] Loading modules backported from Linux version v4.19.85-0-gc63ee2939dc1[ 8.735230] urngd: v1.0.2 started.[ 8.735323] Backport generated by backports.git v4.19.85-1-0-g8a8be258[ 8.754444] <<Marvell Mac80211 Wireless PCIE Network Driver version 10.3.8.0-20181210>>[ 8.762503] pci 0000:00:01.0: enabling device (0140 -> 0142)[ 8.768326] ieee80211 phy0: priv->pcmd_buf = de014000 priv->pphys_cmd_buf = 1e014000[ 8.773003] ieee80211 phy0: fw download start[ 8.889893] ieee80211 phy0: FwSize = 118776 downloaded Size = 118776 curr_iteration 65496[ 9.758978] ieee80211 phy0: fw download complete[ 9.758993] ieee80211 phy0: device node: /soc/pcie/pcie@1,0[ 9.765163] ieee80211 phy0: pcmd = de014000[ 9.781995] ieee80211 phy0: firmware version: 0x702091a[ 9.805283] ieee80211 phy0: firmware region code: 0[ 9.842094] ieee80211 phy0: regdomain: FCC[ 9.842099] ieee80211 phy0: Channel: 36: 0x0 0x0 0xf[ 9.842106] ieee80211 phy0: 15 15 15 15 15 15 15 15 12 12 12 12 10 10 10 10 [ 9.842109] ieee80211 phy0: Channel: 40: 0x0 0x0 0xf[ 9.842116] ieee80211 phy0: 19 19 18 17 19 19 17 15 17 17 17 14 10 10 10 10 [ 9.842119] ieee80211 phy0: Channel: 44: 0x0 0x0 0xf[ 9.842125] ieee80211 phy0: 19 19 18 17 19 19 17 15 17 17 17 14 10 10 10 10 [ 9.842129] ieee80211 phy0: Channel: 48: 0x0 0x0 0xf[ 9.842135] ieee80211 phy0: 1a 1a 18 17 1a 1a 17 15 17 17 17 14 10 10 10 10 [ 9.842138] ieee80211 phy0: Channel: 52: 0x0 0x0 0xf[ 9.842144] ieee80211 phy0: 11 11 11 11 10 10 10 10 12 12 12 12 10 10 10 10 [ 9.842148] ieee80211 phy0: Channel: 56: 0x0 0x0 0xf[ 9.842154] ieee80211 phy0: 11 11 11 11 10 10 10 10 12 12 12 12 10 10 10 10 [ 9.842158] ieee80211 phy0: Channel: 60: 0x0 0x0 0xf[ 9.842164] ieee80211 phy0: 11 11 11 11 10 10 10 10 12 12 12 12 10 10 10 10 [ 9.842167] ieee80211 phy0: Channel: 64: 0x0 0x0 0xf[ 9.842173] ieee80211 phy0: 11 11 11 11 10 10 10 10 12 12 12 12 10 10 10 10 [ 9.842177] ieee80211 phy0: Channel: 100: 0x0 0x0 0xf[ 9.842183] ieee80211 phy0: 10 10 10 10 11 11 11 11 12 12 12 12 10 10 10 10 [ 9.842187] ieee80211 phy0: Channel: 104: 0x0 0x0 0xf[ 9.842193] ieee80211 phy0: 11 11 11 11 10 10 10 10 12 12 12 12 10 10 10 10 [ 9.842196] ieee80211 phy0: Channel: 108: 0x0 0x0 0xf[ 9.842202] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10 [ 9.842206] ieee80211 phy0: Channel: 112: 0x0 0x0 0xf[ 9.842212] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10 [ 9.842216] ieee80211 phy0: Channel: 116: 0x0 0x0 0xf[ 9.842222] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10 [ 9.842225] ieee80211 phy0: Channel: 120: 0x0 0x0 0xf[ 9.842231] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10 [ 9.842235] ieee80211 phy0: Channel: 124: 0x0 0x0 0xf[ 9.842241] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10 [ 9.842244] ieee80211 phy0: Channel: 128: 0x0 0x0 0xf[ 9.842251] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10 [ 9.842254] ieee80211 phy0: Channel: 132: 0x0 0x0 0xf[ 9.842260] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10 [ 9.842264] ieee80211 phy0: Channel: 136: 0x0 0x0 0xf[ 9.842270] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10 [ 9.842273] ieee80211 phy0: Channel: 140: 0x0 0x0 0xf[ 9.842279] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10 [ 9.842283] ieee80211 phy0: Channel: 149: 0x0 0x0 0xf[ 9.842289] ieee80211 phy0: 1a 1a 18 17 19 19 17 15 18 18 17 14 15 15 15 14 [ 9.842292] ieee80211 phy0: Channel: 153: 0x0 0x0 0xf[ 9.842298] ieee80211 phy0: 1a 1a 18 17 1a 1a 17 15 1a 1a 17 14 15 15 15 14 [ 9.842302] ieee80211 phy0: Channel: 157: 0x0 0x0 0xf[ 9.842308] ieee80211 phy0: 1a 1a 18 17 1a 1a 17 15 1a 1a 17 14 15 15 15 14 [ 9.842312] ieee80211 phy0: Channel: 161: 0x0 0x0 0xf[ 9.842318] ieee80211 phy0: 1a 1a 18 17 1a 1a 17 15 1a 1a 17 14 15 15 15 14 [ 9.842322] ieee80211 phy0: Channel: 165: 0x0 0x0 0xf[ 9.842328] ieee80211 phy0: 1a 1a 18 17 1a 1a 17 15 1a 1a 17 14 15 15 15 14 [ 9.843169] ieee80211 phy0: 2G disabled, 5G enabled[ 9.848077] ieee80211 phy0: 2 TX antennas, 2 RX antennas[ 9.853621] pci 0000:00:02.0: enabling device (0140 -> 0142)[ 9.859415] ieee80211 phy1: priv->pcmd_buf = df5d0000 priv->pphys_cmd_buf = 1f5d0000[ 9.863013] ieee80211 phy1: fw download start[ 9.980951] ieee80211 phy1: FwSize = 118776 downloaded Size = 118776 curr_iteration 65511[ 10.838984] ieee80211 phy1: fw download complete[ 10.839011] ieee80211 phy1: device node: /soc/pcie/pcie@2,0[ 10.845184] ieee80211 phy1: pcmd = df5d0000[ 10.861999] ieee80211 phy1: firmware version: 0x702091a[ 10.885291] ieee80211 phy1: firmware region code: 0[ 10.921100] ieee80211 phy1: regdomain: FCC[ 10.921106] ieee80211 phy1: Channel: 1: 0x0 0x0 0xf[ 10.921113] ieee80211 phy1: 19 14 14 14 13 13 13 13 10 10 10 10 0 0 0 0 [ 10.921117] ieee80211 phy1: Channel: 2: 0x0 0x0 0xf[ 10.921123] ieee80211 phy1: 1a 19 18 17 19 19 17 16 14 14 14 14 0 0 0 0 [ 10.921126] ieee80211 phy1: Channel: 3: 0x0 0x0 0xf[ 10.921133] ieee80211 phy1: 1a 19 18 17 19 19 17 16 14 14 14 14 0 0 0 0 [ 10.921136] ieee80211 phy1: Channel: 4: 0x0 0x0 0xf[ 10.921142] ieee80211 phy1: 1a 19 18 17 19 19 17 16 14 14 14 14 0 0 0 0 [ 10.921146] ieee80211 phy1: Channel: 5: 0x0 0x0 0xf[ 10.921152] ieee80211 phy1: 1a 19 18 17 19 19 17 16 14 14 14 14 0 0 0 0 [ 10.921155] ieee80211 phy1: Channel: 6: 0x0 0x0 0xf[ 10.921161] ieee80211 phy1: 1a 19 18 17 19 19 17 16 14 14 14 14 0 0 0 0 [ 10.921165] ieee80211 phy1: Channel: 7: 0x0 0x0 0xf[ 10.921171] ieee80211 phy1: 1a 19 18 17 19 19 17 16 14 14 14 14 0 0 0 0 [ 10.921175] ieee80211 phy1: Channel: 8: 0x0 0x0 0xf[ 10.921181] ieee80211 phy1: 1a 19 18 17 19 19 17 16 14 14 14 14 0 0 0 0 [ 10.921184] ieee80211 phy1: Channel: 9: 0x0 0x0 0xf[ 10.921191] ieee80211 phy1: 1a 19 18 17 19 19 17 16 14 14 14 14 0 0 0 0 [ 10.921194] ieee80211 phy1: Channel: 10: 0x0 0x0 0xf[ 10.921201] ieee80211 phy1: 1a 19 18 17 19 19 17 16 14 14 14 14 0 0 0 0 [ 10.921204] ieee80211 phy1: Channel: 11: 0x0 0x0 0xf[ 10.921210] ieee80211 phy1: 19 15 15 15 14 14 14 14 13 13 13 13 0 0 0 0 [ 10.922057] ieee80211 phy1: 2G enabled, 5G disabled[ 10.927000] ieee80211 phy1: 2 TX antennas, 2 RX antennas[ 10.934021] ip_tables: (C) 2000-2006 Netfilter Core Team[ 10.941261] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)[ 10.958082] xt_time: kernel timezone is -0000[ 10.964728] PPP generic driver version 2.4.2[ 10.969414] NET: Registered protocol family 24[ 10.974800] kmodloader: done loading kernel modules from /etc/modules.d/*[ 12.664710] mvneta f1070000.ethernet eth1: configuring for fixed/rgmii-id link mode[ 12.673132] mvneta f1070000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off[ 12.681593] br-lan: port 1(eth1) entered blocking state[ 12.686884] br-lan: port 1(eth1) entered disabled state[ 12.692292] device eth1 entered promiscuous mode[ 12.701211] br-lan: port 1(eth1) entered blocking state[ 12.706497] br-lan: port 1(eth1) entered forwarding state[ 12.712005] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready[ 12.727733] mvneta f1034000.ethernet eth0: configuring for fixed/sgmii link mode[ 12.735313] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready[ 12.741836] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off[ 12.750688] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready[ 13.298556] ieee80211 phy1: regdomain: ETSI[ 13.302776] ieee80211 phy1: Channel: 1: 0x0 0x0 0xf[ 13.307723] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.313434] ieee80211 phy1: Channel: 2: 0x0 0x0 0xf[ 13.318346] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.324055] ieee80211 phy1: Channel: 3: 0x0 0x0 0xf[ 13.328963] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.334675] ieee80211 phy1: Channel: 4: 0x0 0x0 0xf[ 13.339590] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.345308] ieee80211 phy1: Channel: 5: 0x0 0x0 0xf[ 13.350221] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.355929] ieee80211 phy1: Channel: 6: 0x0 0x0 0xf[ 13.360836] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.366559] ieee80211 phy1: Channel: 7: 0x0 0x0 0xf[ 13.371553] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.377269] ieee80211 phy1: Channel: 8: 0x0 0x0 0xf[ 13.382266] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.387974] ieee80211 phy1: Channel: 9: 0x0 0x0 0xf[ 13.392964] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.398660] ieee80211 phy1: Channel: 10: 0x0 0x0 0xf[ 13.403739] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.409433] ieee80211 phy1: Channel: 11: 0x0 0x0 0xf[ 13.414443] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.420133] ieee80211 phy1: Channel: 12: 0x0 0x0 0xf[ 13.425133] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.430822] ieee80211 phy1: Channel: 13: 0x0 0x0 0xf[ 13.435820] ieee80211 phy1: d d d d d d d d d d d d 0 0 0 0 [ 13.441533] ieee80211 phy0: regdomain: ETSI[ 13.445746] ieee80211 phy0: Channel: 36: 0x0 0x0 0xf[ 13.450740] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.457830] ieee80211 phy0: Channel: 40: 0x0 0x0 0xf[ 13.462823] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.469913] ieee80211 phy0: Channel: 44: 0x0 0x0 0xf[ 13.474912] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.481998] ieee80211 phy0: Channel: 48: 0x0 0x0 0xf[ 13.487000] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.494092] ieee80211 phy0: Channel: 52: 0x0 0x0 0xf[ 13.499086] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.506176] ieee80211 phy0: Channel: 56: 0x0 0x0 0xf[ 13.511169] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.518259] ieee80211 phy0: Channel: 60: 0x0 0x0 0xf[ 13.523257] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.530341] ieee80211 phy0: Channel: 64: 0x0 0x0 0xf[ 13.535340] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.542425] ieee80211 phy0: Channel: 100: 0x0 0x0 0xf[ 13.547512] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.554603] ieee80211 phy0: Channel: 104: 0x0 0x0 0xf[ 13.559684] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.566774] ieee80211 phy0: Channel: 108: 0x0 0x0 0xf[ 13.571854] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.578945] ieee80211 phy0: Channel: 112: 0x0 0x0 0xf[ 13.584031] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.591116] ieee80211 phy0: Channel: 116: 0x0 0x0 0xf[ 13.596202] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.603296] ieee80211 phy0: Channel: 120: 0x0 0x0 0xf[ 13.608376] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.615466] ieee80211 phy0: Channel: 124: 0x0 0x0 0xf[ 13.620547] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.627637] ieee80211 phy0: Channel: 128: 0x0 0x0 0xf[ 13.632716] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.639806] ieee80211 phy0: Channel: 132: 0x0 0x0 0xf[ 13.644893] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.651977] ieee80211 phy0: Channel: 136: 0x0 0x0 0xf[ 13.657062] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.664152] ieee80211 phy0: Channel: 140: 0x0 0x0 0xf[ 13.669233] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.676323] ieee80211 phy0: Channel: 149: 0x0 0x0 0xf[ 13.681403] ieee80211 phy0: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 [ 13.689125] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready[ 14.097994] ieee80211 phy0: change: 0xffffffff[ 14.242313] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready[ 14.250049] br-lan: port 2(wlan0) entered blocking state[ 14.255452] br-lan: port 2(wlan0) entered disabled state[ 14.260981] device wlan0 entered promiscuous mode[ 14.265831] br-lan: port 2(wlan0) entered blocking state[ 14.271188] br-lan: port 2(wlan0) entered forwarding state[ 14.283710] ieee80211 phy0: change: 0x100[ 14.296837] ieee80211 phy0: change: 0x40[ 14.523038] ieee80211 phy0: change: 0x40[ 14.590042] ieee80211 phy1: change: 0xffffffff[ 14.710373] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready[ 14.717368] br-lan: port 3(wlan1) entered blocking state[ 14.722711] br-lan: port 3(wlan1) entered disabled state[ 14.728218] device wlan1 entered promiscuous mode[ 14.733015] br-lan: port 3(wlan1) entered blocking state[ 14.738357] br-lan: port 3(wlan1) entered forwarding state[ 14.742996] ieee80211 phy0: change: 0x40[ 14.748135] br-lan: port 2(wlan0) entered disabled state[ 14.754007] br-lan: port 3(wlan1) entered disabled state[ 14.851024] ieee80211 phy0: change: 0x100[ 14.897803] ieee80211 phy0: change: 0x100[ 14.910067] ieee80211 phy0: change: 0x42[ 15.089050] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready[ 15.095542] br-lan: port 2(wlan0) entered blocking state[ 15.100890] br-lan: port 2(wlan0) entered forwarding state[ 15.106813] ieee80211 phy1: change: 0x100[ 15.119908] ieee80211 phy1: change: 0x42[ 15.283048] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready[ 15.289510] br-lan: port 3(wlan1) entered blocking state[ 15.294872] br-lan: port 3(wlan1) entered forwarding state[ 15.428346] IPv6: ADDRCONF(NETDEV_UP): wlan1-1: link is not ready[ 15.488382] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready[ 15.682086] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready[ 15.688885] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready[ 15.832321] ieee80211 phy1: change: 0x20[ 15.855787] ieee80211 phy0: change: 0x20
Community Builds
Community Build details for the WRT AC Series (including this router) can be found here.
Notes
Space for additional notes, links to forum threads or other resources.
The v1 and v2 devices are identical for flashing purposes.
The v2 was released at a later date after Linksys moved towards locking down the wifi power tables in the EEPROM
You may find additional/supplementary information at the wrt_ac_series page
Tags
How to add tags
mvebu, mwlwifi, U-boot, 128flash, 512ram, U-boot, Dual firmware, 2NIC, 2WNIC, 5Port, 2core, ARMv7, GigabitEthernet, JumboFrames, VLAN, MiniPCIexpress, wlan, 802.11ac, 802.11abgn, mu-mimo, DetachableAntenna, 2Ant, USB, 2USB, USB2.0, USB3.0, sata2, esata, crypto, JTAG, Serial, 1button, 12v powered
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
![[OpenWrt Wiki] Linksys WRT1200AC (2024)](data:image/png;base64,iVBORw0KGgoAAAANSUhEUgAAAAEAAAABCAQAAAC1HAwCAAAAC0lEQVR42mP8/h8AAvMB+NzmkbcAAAAASUVORK5CYII=)